Become our sponsor and display your banner here
Page 4 of 14 FirstFirst 12345678 ... LastLast
Results 31 to 40 of 136

Helmet covers

Article about: It looks like he has one of the pocket on top of his helmet I agree on the pic Mark

  1. #31
    ?

    Default Re: Helmet covers

    Cool Dan Andy sent me measurements of a 68 shell. I just need to know if i got a 62 or 64.

    Cheers

  2. #32

    Default Re: Helmet covers

    Quote by KradSpam View Post
    I think I have an idea which one that might be Dan
    Thought you might Andy! and looking forward to doing some "distressing" to it ( the cover, not the helmet! )

    Cheers, Dan
    " When you're chewing on life's gristle, don't grumble, give a whistle "

  3. #33

    Default Re: Helmet covers

    Quote by Datrus View Post
    Cool Dan Andy sent me measurements of a 68 shell. I just need to know if i got a 62 or 64.

    Cheers
    I measured a few M35 M40 size 64 shells from different makers and they were 230-235mm side to side and 280-285 front to back ( measured at the skirt edges )
    Dan
    " When you're chewing on life's gristle, don't grumble, give a whistle "

  4. #34

    Default Re: Helmet covers

    Quote by Datrus View Post
    If any of you have a 64-62 helmet, could you take a measurement of the outside diameter? Around the liner rivets.

    Regards, Lars
    And the outside circumference at the rivet position is 660-665mm

    Dan
    " When you're chewing on life's gristle, don't grumble, give a whistle "

  5. #35

    Default Re: Helmet covers

    I have an ET68 that I would LOVE to put one of these on, if you've got the extra fabric.
    Last edited by ObKrieger; 09-09-2012 at 03:08 PM. Reason: Not an EF66... an ET68 :)

  6. #36
    ?

    Default Re: Helmet covers

    Quote by Danmark View Post
    And the outside circumference at the rivet position is 660-665mm

    Dan
    Thanks a lot Dan We will start the production. She will hand stitch them.

    Regards, Lars

    - - Updated - -

    Quote by ObKrieger View Post
    I have an ET68 that I would LOVE to put one of these on, if you've got the extra fabric.
    No problem We'll make one.

    Regards, Lars

  7. #37
    ?

    Default Re: Helmet covers

    Hello Dan,

    There is something "fishy" about your measurements except for the circumference Are you under the influence of the infamous Inch maybe? Below are the measurements of my helmet. I will say it's a 62 judging from the 660-665mm of your 64 lid. Thanks mate.

    Front to back skirt 43.5 cm. Side to side 42.5 cm. Circumference 63.5 just under the retaining pins.

    Regards, Lars

  8. #38

    Default Re: Helmet covers

    HI Lars, just measured again - got the same measurements - checked the tape - it is in metric. I measured 4 helmets ( all Quists and all clearly stamped Q64 ) 2 x M35 and 2 x M35. I turned them upside down and measured side to side at the skirt edge and then front to back hooking the tape edge over the visor and measuring back to the skirt edge at rear. I will take some photos with the tape after work today and you can see ....... strange I agree my measurements are quite different to yours????

    Dan
    " When you're chewing on life's gristle, don't grumble, give a whistle "

  9. #39
    ?

    Default Re: Helmet covers

    I think what the problem is Dan. I am measuring from skirt to skirt but up around the dome. You measure across right?

    Regards, Lars

  10. #40

    Default Re: Helmet covers

    Quote by Datrus View Post
    I think what the problem is Dan. I am measuring from skirt to skirt but up around the dome. You measure across right?

    Regards, Lars
    Yes, I am measuring across, not up and over. NOW I understand, I will sent some new measurements!
    Cheers, Dan
    " When you're chewing on life's gristle, don't grumble, give a whistle "

Page 4 of 14 FirstFirst 12345678 ... LastLast

Similar Threads

  1. Marine Helmet Covers

    In US M1 steel helmet forum
    07-19-2012, 09:55 PM
  2. Question M1 Helmet Covers

    In US M1 steel helmet forum
    03-26-2012, 10:11 PM
  3. M1 Camo Helmet Covers

    In US M1 steel helmet forum
    04-05-2011, 08:24 AM
  4. W.W.2 U.S.M.C . Camo Helmet Covers

    In US M1 steel helmet forum
    11-27-2010, 10:18 PM
  5. SS Camo Helmet Covers

    In SS Uniforms and insignia
    05-14-2010, 10:03 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •